Thanks Thanks:  17
Likes Likes:  61
Page 3 of 3 FirstFirst 1 2 3
Results 21 to 28 of 28

Thread: Ruger Single Six

  1. #21
    Platoon Sgt Pat C.'s Avatar
    Join Date
    Jun 2020
    Location
    USA
    Rounds Down Range
    1,515
    Post Thanks / Like

    Re: Ruger Single Six

    CCI TARGET offhand at 20 yards.
    Attached Images Attached Images

  2. Thanks 4570govt thanked for this post
  3. #22
    Moderator 4570govt's Avatar
    Join Date
    Mar 2011
    Location
    Charlotte, Arkansas
    Rounds Down Range
    17,249
    Post Thanks / Like

    Re: Ruger Single Six

    That looks good, what is the spread on that, 6 inches?
    "Keep 'em in the 10 Ring!"

    Member M14 Battle Rifle Club Board of Directors


  4. Thanks Pat C. thanked for this post
  5. #23
    Platoon Sgt Pat C.'s Avatar
    Join Date
    Jun 2020
    Location
    USA
    Rounds Down Range
    1,515
    Post Thanks / Like

    Re: Ruger Single Six

    The black is 6" circle , For 4 3/4" barrel at 20 that may be all I'm capable of in current configuration. What I'm going to do is machine a fine target bead front ramp and a fine U notch rear blade . Goal is to keep 3" circle offhand at 20

  6. #24
    Moderator 4570govt's Avatar
    Join Date
    Mar 2011
    Location
    Charlotte, Arkansas
    Rounds Down Range
    17,249
    Post Thanks / Like

    Re: Ruger Single Six

    Quote Originally Posted by Pat C. View Post
    The black is 6" circle , For 4 3/4" barrel at 20 that may be all I'm capable of in current configuration. What I'm going to do is machine a fine target bead front ramp and a fine U notch rear blade . Goal is to keep 3" circle offhand at 20
    That's good shooting!
    "Keep 'em in the 10 Ring!"

    Member M14 Battle Rifle Club Board of Directors


  7. Thanks Pat C. thanked for this post
    Likes VanHahner liked this post
  8. #25
    Platoon Sgt Pat C.'s Avatar
    Join Date
    Jun 2020
    Location
    USA
    Rounds Down Range
    1,515
    Post Thanks / Like

    Re: Ruger Single Six

    The Ruger experts on rimfire central say a trigger job must be done to get the most out of single six. I might try some reduced power springs and Stone the machine marks of trigger and hammer notches too and see what that will yield.

  9. #26
    Platoon Sgt Pat C.'s Avatar
    Join Date
    Jun 2020
    Location
    USA
    Rounds Down Range
    1,515
    Post Thanks / Like

    Re: Ruger Single Six

    Shot this 50ft kneeling two hand with CCI TARGET .Used
    6 O'clock hold .had two flyers
    Attached Images Attached Images

  10. #27
    Machine Gunner
    Join Date
    Jun 2020
    Location
    Ct
    Rounds Down Range
    154
    Post Thanks / Like

    Re: Ruger Single Six

    I was going to say to try the magnum cylinder if you have one. Sometimes the convertible models run better with one or the other.

    The ammo that performed did it have a waxy type of lube? Many target rimfire rounds do and also have a slightly larger bullet diameter to engrave the rifling or snug up upon chambering. Hi vel copper washed are meant for the semi auto plinkers and run well for that but not the best for good groups on paper.

    Also, you're firing 30 or so rounds per target, you may get an average smaller group size by firing multiple 10 round groups. It's a numbers thing, long haul averages and all that numbers stuff.

    You can check with Ruger as they may say to return it for a new in spec cylinder. During the frenzy a lot of firearms were sent that had issues, my understanding is they'll make good if it's not performing well.

    If you do return it do so with the factory springs installed, they'll remove any aftermarket parts and charge you for the 'fix'.

  11. #28
    Platoon Sgt Pat C.'s Avatar
    Join Date
    Jun 2020
    Location
    USA
    Rounds Down Range
    1,515
    Post Thanks / Like

    Re: Ruger Single Six

    This revolver is over 30 years old , nothing wrong with it. First two cylinders full 12 shots were all in the black .I'm cheap I get my money worth out of targets ,Ha.
    My near 54 old eyes ain't what they used to be , offhand too.
    What my plan is to machine a slot in the ramp for a fine bead blade type target sight and fab a shallow U notch rear .

    This coupled with trigger job I see no problem keeping them in the black offhand at 20.

  12. Likes blkgunlvr, 4570govt, JEFFJP_N_JJ liked this post
Page 3 of 3 FirstFirst 1 2 3

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •